Kval 994-X Скачать руководство пользователя страница 85

Страница: 85 / 130

Machine Component Terms

4-3

KVAL 994-X Operation Manual

Machine Component Terms

This table includes definitions of common terms.

Machine Terminology

Machine

Electrical Panels

Electrical Panels contain the brains and power for the machine. The

Main Electrical Panel contains the main PLC and servo drives. The

High Frequency Panels contain the VFD’s drive routers, width

adjust, and feed motors.

Door Clamp

The door clamp secures the door for stable routing and drilling.

Jamb Clamp

The jamb clamp secures the jamb to hold it in place as routing and

drilling.

Door Stop

The door stop sets the door in the correct position for processing.

Jamb Stop

The jamb stop sets a reference for the jamb to be in the correct posi

tion for processing. It is located on the front section of the machine

and is set manually by the operator.

Tools

Routers

Routers are located in the Carriage Heads and on the Back Section.

The routers rout the hinge pockets and rout face plates. Typically

Carriage Heads contain two routers that cut in the opposite direc

tions to create a smooth cut.

Bolt Drill

The bolt drill is located on the back section. Drills a bolt hole on the

lock edge of the door.

Lock Bore

The lock bore is located on the back section. It drills a lock hole on

the face of the door.

Pre-drills

The pre-drills are located in the Carriage Heads. They pre-drill screw

holes for hinge screw application on the door and jamb.

Chisels

(Opt CH)

Chisels are located in the Carriage Heads and the back section. The

chisels square the corners on the hinge pockets and the lock plate.

Chip-Out Block

Chip-Out Blocks are located under some drills to reduce tear-out on

the edges of the cut.

Operation

Operator’s Station

The Operator’s Station is the interface of operator and machine. It

contains power controls and touch screen interface to control the

cutting parameters of the door.

Machine Control

Located mid machine, manually set Feed (Auto-Man), LH or RH

door, Start and Stop machine.

Door Clamp Pedal

The Door Clamp Pedal is a foot pedal that activates the Door Clamp

to either clamp or unclamp the door.

Jamb Clamp Pedal

The Jamb Clamp Pedal is a foot pedal that activates the Jamb

Clamp to either clamp or unclamp the jamb.

Six-Shooter

The Six-Shooter is located at the left side of the machine. Six Shoot

ers apply hinges and the secures them with screws. (3x3 pattern)

Eight-Shooter

(Opt K)

The Eight -Shooter is located at the left side of the machine.Eight

Shooters apply hinges and the secures them with screws. (4x4 pat

tern)

Содержание 994-X



































































































































Результаты поиска

Содержание 994-X

Отзывы:

Kval 994-X, Руководство по эксплуатации, Страница: 85 / 130

Результаты поиска

Содержание 994-X

Отзывы: