Kval 994-X Скачать руководство пользователя страница 56

Страница: 56 / 130

About the Diagnostic Screen

KVAL 994-X Operation Manual

2-26

About the Diagnostic Screen

The Diagnostic Screen displays all the tasks the

994-X

performs. This screen can help with trou

bleshooting by associating an error code to machine sections or functions. The top line will have

the most current routine that is running. If the machine issue cannot be resolved, call

KVAL Inc.

(1-

800-553-5825). Have the error code that is displayed, ready to give the KVAL representative.

This will aid in troubleshooting and shorten downtime.
The Diagnostic Screen keeps track of the all the doors processed on the machine. The quantity is

displayed in the

Total Door Count

box.

To keep track of daily production, the quantity of doors produced in a day is displayed in the

Daily

Door Count

box. This count can be reset with the

Reset Count

button.

FIGURE 2-8.

Diagnostic Screen

Production Tracking Tools

Содержание 994-X



































































































































Результаты поиска

Содержание 994-X

Отзывы:

Kval 994-X, Руководство по эксплуатации, Страница: 56 / 130

Результаты поиска

Содержание 994-X

Отзывы: