Kval 994-X Скачать руководство пользователя страница 13

Страница: 13 / 130

Overview of the 994-X Door Hanging System

1-5

KVAL 994-X Operation Manual

Option

Servo Backsection with Cor

ner Squaring

The 994-X system combines very high quality hardware

detailing, with high speed productivity. Unique features

include computer controlled ball screw movements for all

router and chisels, complete with square lock face plates.

Backsection will have the ability to machine a face plate

at both "0" and "3" degree. Operator can select widths

from 1" to 1-1/4" wide and up to 2-3/4" in length.

Option

Zero & Three Degree Hinge

Routing

Price includes PLC logic and controls to allow front hinge

routing section to rout on either a 0 degree or 3 degree

angle.
Hinges will be flush mounted when installed on doors

with either square edge or 3 degree bevel on hinge side

Option

Top Hinge Dimension Differ

ent for 6'-8" and 8'-0" Door

In-feed door and jamb stops will be movable. Door stop

will be cylinder actuated.
NOTE: Specifications for hinge locations must be pro

vided in order to prepare quotation.

Option

Hinge Stops for 6'8", 7'0" &

8'0" Doors

This option is limited to certain hinge pocket locations.

Hinge location specifications need to be submitted in

order to determine if they can be accommodated with the

994-X.

Option Z Screw-Changing Hopper for

Six Shooter

Screw-changing hopper for changing screw colors.

Option

Quick-Change Hopper for

Eight Shooter

Screw changing hopper for Eight Shooter allows for rapid

change of screw colors.

Quick Change Knuckle Hinge Switch located on the Eight Shooter hinge applicator

which provides the ability to switch from a standard (nar

row barrel) knuckle hinge to a wide spring-knuckle hinge.

Changeover time between knuckle sizes is 1 second.

Narrow Door Support

Supports doors between 12" - 16”
Structure utilizes air cylinders and 7 pairs of industrial

wheels for support - mechanism is automatically put in

and out of position via a selection

Split Jamb Staplers

Two 1/4" crown staple guns are mounted onto the jamb

clamp brackets. While clamped in the machine, staples

will be driven into the back side of the split jamb to keep

the male and female together.
The staple guns are fired with a single valve that is inter

locked with a safety switch to disable the staple guns

unless there is a jamb clamped in the machine.
Two staple guns with remote fires are required and are

not included in the price of the option.

Option Title

Description

Содержание 994-X



































































































































Результаты поиска

Содержание 994-X

Отзывы:

Бренды по названию

Популярные бренды

Kval 994-X, Руководство по эксплуатации

Результаты поиска

Содержание 994-X

Отзывы:

Бренды по названию

Популярные бренды