Kval 994-X Скачать руководство пользователя страница 44

Страница: 44 / 130

About the Main Screen

KVAL 994-X Operation Manual

2-14

Back Section Group

Set the lock parameters

in the

Back Section

group. The settings

include lock specifica

tions for different lock

settings, the ability to

enable

and

disable

the

lock bore, bolt drill and face plate routing.

Fast Plate can be

enabled or disab

led.

Can Disable or enable the

Ball Catch

function if applicable.

Lock Backset (Option)

shows the backset for each head.

Auto Enable and Disable Buttons and Screw Hopper

Auto Feed (Option):

Press

Auto Feed

to toggle the auto feed on or off.

In auto

mode, the feed system will bring in and clamp a door, wait for

processing to complete, then feed the door out.

Feed Through (Option):

Press

Feed Through

to toggle the feed

through on or off. In feed through mode, the door will pass through the

machine without processing.

Auto Width:

Press

Auto Width

to toggle the auto width on or off. In

auto width mode, the machine will automatically set the width adjust

system for optimum clamping.

Auto Unclamping:

Press

Auto Unclamping

to toggle auto unclamping on or off. The

auto unclamp button sets the machine to automatically unclamp the door after

machining is completed.

Screw Hopper

Control the Hoppers At the main menu.
Select the desired

Hopper Button

to enable for

production. The Hopper button will display the

label that is assigned in the manual screen.
Enable or disable the Automatic Screw Drop.
Press the

Manual Air Injection

to deliver a burst of

air to the drop location to free any stuck screws or

push a screw through.

Содержание 994-X



































































































































Результаты поиска

Содержание 994-X

Отзывы:

Похожие инструкции для 994-X

Бренды по названию

Популярные бренды

Kval 994-X, Руководство по эксплуатации

Результаты поиска

Содержание 994-X

Отзывы:

Похожие инструкции для 994-X

Бренды по названию

Популярные бренды