Kurzweil SP7 Grand Скачать руководство пользователя | Manualshive

Страница: 52 / 64

background image

The control buttons consist of 8 colored LED buttons, numbered B1 through B8, below the control knob.

The Buttons Edit page lets you edit the Controller, Color, Destination, Target, Off Value, On Value and Initial State

parameters.

Buttons-EDIT

Select the button to be edited from among the eight buttons, B1 to B8. Other buttons can be changed in
the same way.

Controller

You can change the color of the assigned buttons by selecting a color from the 42 available color palette.
Other buttons can be changed in the same way.

Color

Set the value from 0 to 127 when the controller button is off.

Off Value

Set the value from 0 to 127 when the controller button is on.

On Value

Destination specifies the function to be assigned to the controller.

Destination consists of 8 categories : System, MIDI CC, AUX Effect (AUX FX), AUX EQ (AUX EQ), Zone
Insert Effect (Zone IFX), Audio Effect (Audio FX), Vocal Processor (Vocal Proc), Notes. Within each
category, you can specify detailed controllers. [See Appendix-A (Controller Destination), Appendix-B
(MIDI Destination)]

Destination

It can be specified differently depending on the selected destination.

Depending on the destination assigned to each controller, you can select None, Preset, System,
Zone1~16, Zone ALL, FX A~D, FX ALL, Input 1~2, Input ALL, etc.

Target

Chapter 5.

Global Mode

«
...
50
51
52
53
54
...
»

Содержание SP7 Grand

































































Отзывы:

Нет отзывов

Похожие инструкции для SP7 Grand

Бренд: Campbell Страницы: 18

Бренд: Vector Страницы: 4

Бренд: Eclipse Combustion Страницы: 46

Бренд: Bard Страницы: 2

Бренд: Unitary products group Страницы: 28

Бренд: Halyard Страницы: 88

Бренд: HALDER Страницы: 2

Бренд: Malekko Страницы: 2

Бренд: Major Страницы: 26

Бренд: Ofa Bamberg Страницы: 80

Бренд: Quincy Страницы: 31

Lyme FIA Sofia 2

Бренд: Quidel Страницы: 49

Бренд: Quest Leisure Products Страницы: 12

Бренд: UniPix Страницы: 24

Бренд: Dräger Medical Страницы: 92

Бренд: SUHNER MACHINING Страницы: 30

Бренд: Qtx Страницы: 6

Бренд: Electro-Music Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды