Kurzweil SP7 Grand Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 64

background image

Chapter 1.

Started

1-6. The Rear Panel

Power Switch

USB Port

MAIN OUT

HEADPHONE Jack

AUDIO IN

PEDALS

DC Power Jack

MIDI Port

SD Card Slot

MONITOR OUT

Use the AUDIO IN jacks to mix external audio sources with the sounds of the SP7, apply effects to external audio
sources, or route external audio sources to a computer for recording or processing in a DAW. This is useful for
playing along with backing tracks from a portable music player, computer, or other electronic instrument.

Note :

If you turn up the INPUT GAIN knobs with nothing connected to the rear panel AUDIO INPUT jacks,

unwanted noise may occur. As such, it is best practice to set the INPUT GAIN knobs to their minimum values

when no audio source is connected.

AUDIO INPUT Combo Jacks

Connect headphones to the 1/4-inch HEADPHONE jack located on the left rear panel. Headphone volume can
be adjusted through the front panel MONITOR knob. You will need a
1/8-inch-to-1/4-inch adapter in order to use headphones that have a smaller mini plug connector.

Note :

The HEADPHONE and MONITOR OUT share the same audio bus and are both controlled by the MONITOR

volume knob.

HEADPHONE Jack

Connect an amplifier or mixer to the MONITOR OUT 1/4-inch jacks.
The volume is adjusted using the MONITOR volume knob on the front panel.

Note :

The HEADPHONE and MONITOR OUT share the same audio bus and are both controlled by the MONITOR

volume knob.

MONITOR OUT - LEFT (MONO) and RIGHT jacks

Connect an amplifier or mixer to the MAIN OUT 1/4-inch jacks.
The volume is adjusted using the MAIN volume knob on the front panel. For a mono signal, only use the LEFT
(MONO) jack and leave the RIGHT jack unplugged.

MAIN OUT - LEFT (MONO) and RIGHT jacks

«
...
10
11
12
13
14
...
»

Содержание SP7 Grand

































































Отзывы:

Нет отзывов

Похожие инструкции для SP7 Grand

Бренд: Laica Страницы: 4

Бренд: GE Страницы: 242

Бренд: GE Страницы: 24

Бренд: Balanced Body Страницы: 3

Бренд: SAMCHULLY Страницы: 48

Бренд: ACE INSTRUMENTS Страницы: 15

Бренд: Wave Fitness Страницы: 15

Бренд: Dana Design Страницы: 20

Бренд: Farmi Forest Corporation Страницы: 32

Бренд: ParaBody Страницы: 5

Бренд: Launch Страницы: 3

Бренд: Launch Страницы: 43

Бренд: Launch Страницы: 8

Бренд: Launch Страницы: 67

Бренд: Launch Страницы: 55

Бренд: LAUNCH TECH Страницы: 14

X-431 PROS V4.0

Бренд: Launch Страницы: 80

Бренд: Park House Healthcare Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды