manualshive.com logo in svg

Kurzweil KDFX V2 - MUSICIANS REFERENCE REV B, Справочник

Поделиться
Скачать
Kurzweil KDFX V2 - MUSICIANS REFERENCE REV B Скачать руководство пользователя страница 69

Algorithm Reference

Compress

3-29

746 Compress

A reverb and compressor in series.

PAUs:

2 

Compress is configured as a reverb followed by a compressor. The reverbs used are the same as 
MiniVerb. The compressor is a soft-knee compressor and can be configured as a feed-forward or feedback 
compressor.

Figure 12

Simplified block diagrams of Compress

The main control for the reverbs is the Rv Type parameter. Rv Type changes the structure of the algorithms 
to simulate many carefully crafted room types and sizes. Spaces characterized as booths, small rooms, 
chambers, halls and large spaces can be selected. For a complete discussion on the reverbs see the sections 
on MiniVerb.

The compressor reduces the signal level when the signal exceeds a threshold. The amount of compression 
is expressed as a ratio. The compression ratio is the inverse of the slope of the compressor input/output 
characteristic. The amount of compression is based on the sum of the magnitudes of the left and right 
channels. A compression ratio of 1:1 will have no effect on the signal. An infinite ratio, will compress all 
signal levels above the threshold level to the threshold level (zero slope). For ratios in between infinite and 
1:1, increasing the input will increase the output, but by less than it would if there was no compression. 
The threshold is expressed as a decibel level relative to digital full-scale (dBFS) where 0 dBFS is digital 
full-scale and all other available values are negative.

In the soft-knee compressor there is a gradual transition from compressed to unity gain.

 

Figure 13

Soft-Knee compression characteristics

To determine how much to compress the signal, the compressor must measure the signal level. Since 
musical signal levels will change over time, the compression amounts must change as well. You can 
control the rate at which compression changes in response to changing signal levels with the attack and 
release time controls. With the attack time, you set how fast the compressor responds to increased levels. 
At long attack times, the signal may overshoot the threshold level for some time before it becomes fully 
compressed, while at short attack times, the compressor will rapidly clamp down on the level. The release 

L Input

R Input

Reverb

Compress

L Output

R Output

Out 

Amp

In Amp

Threshold

Содержание KDFX V2 - MUSICIANS REFERENCE REV B

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды