manualshive.com logo in svg

Kurzweil KDFX V2 - MUSICIANS REFERENCE REV B, Справочник

Поделиться
Скачать
Kurzweil KDFX V2 - MUSICIANS REFERENCE REV B Скачать руководство пользователя страница 103

Algorithm Reference

CompressDualTime

3-63

Parameters:

Page 1

Page 2

In/Out

When set to In the compressor is active; when set to Out the compressor is bypassed.

Out Gain

The output gain parameter may be used to increase the gain by as much as 24 dB, or 
reduce the gain to nothing. Note that the Out Gain parameter does not control the signal 
level when the algorithm is set to Out.

SC Input

Select the input source channel for side-chain processing—left (L), right (R) or both 
(L & R). When set to L & R, the maximum amplitude is used.

ComprsChan

Select which input channel will receive compression processing—left, right or both. If you 
select left or right, the opposite channel will pass through unaffected.

FdbkComprs

A switch to set whether the compressor side chain is configured for feed-forward (Out) or 
feedback (In).

Atk Time

The time for the compressor to start to cut in when there is an increase in signal level 
(attack) above the threshold.

Rel Time A

The time for the compressor to stop compressing when there is a reduction in signal level 
(release) from a signal level above the threshold. This release time is active while the 
signal is reduced by more than the release threshold setting.

Rel Time B

The time for the compressor to stop compressing when there is a reduction in signal level 
(release) from a signal level above the threshold. This release time is active while the 
signal is reduced by less than the release threshold setting.

Rel Thres

When the signal is reduced by more than this release threshold, the release time is set by 
Rel Time A. Otherwise the release time is set by Rel Time B.

SmthTime

A lowpass filter in the control signal path. It is intended to smooth the output of the 
compressor’s envelope detector. Smoothing will affect the attack or release times when 
the smoothing time is longer than one of the other times.

Signal Dly

The time in ms by which the input signal should be delayed with respect to compressor 
side chain processing (i.e. side chain predelay). This allows the compression to appear to 
take effect just before the signal actually rises.

In/Out

In or Out

Out Gain

Off, -79.0 to 24.0 dB

FdbkComprs

In or Out

SC Input

L, R, L & R

Signal Dly

0.0 to 25.0 ms

ComprsChan

L, R, L & R

Atk Time

0.0 to 228.0 ms

Ratio

1:1.0 to 1:17.0

Rel Time A

0 to 3000 ms

Comp Thres

-79.0 to 0.0 dB

Rel Time B

0 to 3000 ms

Rel Thres

-79.0 to 0.0 dB

SmthTime

0.0 to 228.0 ms

MakeUpGain

Off, -79.0 to 24.0 dB

||||||||||||||||||||||||||||||

Reduction

-dB        40            20        12        8            6          4          2            0

Содержание KDFX V2 - MUSICIANS REFERENCE REV B

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды