manualshive.com logo in svg

Kurzweil KDFX V2 - MUSICIANS REFERENCE REV B, Справочник

Поделиться
Скачать
Kurzweil KDFX V2 - MUSICIANS REFERENCE REV B Скачать руководство пользователя страница 46

3-6

Algorithm Reference

Degen Regen BPM

TnLFODepth The output delay taps (1 and 2) will have their positions modulated by an LFO (internal to 

the FX processor) if the TnLFODepth parameter is non-zero. A moving tap on a delay line 
will result in a pitch shift, and TnLFODepth sets the maximum pitch shift (up and down) 
in cents.

TnLFOPhase

Specifies the phase angle of the output LFO tap (1 or 2) relative to the other output LFO 
tap, the feedback (loop) LFO tap, and the system (or MIDI) tempo clock, if turned on (see 
Tempo). For example, if one LFO is set to 0° and another is set to 180°, then when one LFO 
delay tap is at its shortest, the other will be at its longest. If the system (or MIDI) tempo 
clock is turned on, the LFOs are synchronized to the clock with absolute phase. 

Tapn  Delay

The delay length of the output tap 1 or 2. In Degen Regen BPM, the tap length is specified 
as a fraction or multiple of the tempo, in “beats.” The length of a delay tap in seconds can 
be calculated from beats as T = (beats/tempo)

 

❃

 

60.

Tapn  Level

The level of the output tap 1 or 2 expressed as a percent.

Tapn  Pan

The output taps 1 and 2 are mono sources that can be panned to the left or right output 
channels. A pan setting of -100% is fully left while 100% is fully right.

Comp Atk

The time for the compressor to start to cut in when there is an increase in signal level 
(attack) above the threshold.

Comp Rel

The time for the compressor to stop compressing when there is a reduction in signal level 
(release) from a signal level above the threshold.

CompSmooth A lowpass filter in the compressor control signal path. It is intended to smooth the output 

of the expander’s envelope detector. Smoothing will affect the attack or release times 
when the smoothing time is longer than one of the other times.

Comp Ratio

The compression ratio. High ratios are highly compressed; low ratios are moderately 
compressed.

Comp Thres

The threshold level in dBFS (decibels relative to full scale) above which the signal begins 
to be compressed.

Dist Drive

Applies a boost to the feedback signal to overdrive the distortion algorithm. When 
overdriven, the distortion algorithm will soft-clip the signal. Since distortion drive will 
make your signal very loud, you may have to reduce the feedback amount or turn on the 
compressor as the drive is increased.

DistWarmth

A lowpass filter in the distortion control path. This filter may be used to reduce some of 
the harshness of some distortion settings without reducing the bandwidth of the signal.

Содержание KDFX V2 - MUSICIANS REFERENCE REV B

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды