KUKEN PTS-800 EX Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 24

background image

This section describes how to select and set each mode.
Please follow the instruction below.

① Make sure the machine is turned off.

Press ③ for a few second and press the power
switch while pressing ③.

② Press ① key once to change the mode from the [Prn].

And press ① again to change the mode back to [PC]

If the PTS is non-transmission model, either can be selected.

③ Press ② to complete the selection.

Then the selection will move to the next setting.

④ Press ① key once to change the mode from the [Aut].

And press ① again to change the mode back to [Ind].

⑤ Press ② to complete the selection.

Then the selection will move to the next setting.

⑥ Press ① key once to change the mode from the [CH1] on.

And press ① again to change the mode back to [CH-] off.

⑦ Press ② to complete the selection.

After the selection of [CH1], the power will be turned off.

Preparation (2)-②

Initial Setting ( Operation )

To select Transmission Mode

To select Loosening Mode

To select [ CH1 ] Mode

keep on pressing

Press to turn on

«
...
6
7
8
9
10
...
»

Содержание PTS-800 EX

























Отзывы:

Нет отзывов

Похожие инструкции для PTS-800 EX

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды