KUHN RW1600 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 102

background image

14

Safety instructions

Road transport

Pay attention to a road-safe condition

When driving on the local roads, the machine must correspond to the
current traffic prescriptions. To which e.g. belongs:

•

mounting of lighting, warning and protection installations

•

comply with the permittable transport dimensions and weights,
maximum permittable axle loads, tyre carrying capacity, total
weights and national speed limits

•

taking care of the maximum permitted speed of 25 km/h

In case of negligence, driver and owner of the machine are fully liable.

Prohibition of transporting people on the machine

Nobody and nothing shall be transported on the machine during
transport. Transporting of people or objects on the machine is perilous
and prohibited.

Changed driving and braking handling

Because of the hitched machine the driving and braking handling
changes. Especially when driving curves the dimensions and mass of
the machine have to be taken into account. A not adapted driving style
can lead to accidents.

Adapted driving speed

Under bad road circumstances and at high driving speeds very high
crafts can appear, which load or overload the tractor and machine to
much. Adapt the driving speed according to the road circumstances.
A not adapted driving speed can lead to accidents.

«
...
12
13
14
15
16
...
»

Содержание RW1600







































































































Отзывы:

Нет отзывов

Похожие инструкции для RW1600

Бренд: Bartscher Страницы: 22

Бренд: Daga Страницы: 24

Бренд: DAF Страницы: 68

Бренд: DANLERS Страницы: 2

Бренд: Haas Automation Страницы: 26

Бренд: EAW Страницы: 2

Бренд: abc Страницы: 28

Бренд: Gary Machinery Страницы: 14

Бренд: quadient Страницы: 14

Бренд: Qu-Bit Electronix Страницы: 31

Бренд: Haas Страницы: 12

Бренд: SaMASZ Страницы: 25

Бренд: Yamaha Страницы: 39

Бренд: Yamaha Страницы: 110

Бренд: Salter Страницы: 18

Бренд: Salter Страницы: 42

Бренд: Salter Страницы: 47

Бренд: Salter Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды