KUHN RW1600 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 102

background image

Hitching the machine

33

Connections

Hydraulic

connections

Hydraulic coupling only pressureless

Only couple the hydraulic hoses to the tractor when both tractor and
machine hydraulics are pressureless. Hydraulics under pressure can
cause accidental movements of the machine.

Avoid oil mixture

When using the machine in combination with different tractors,
improper oil mixture can take place. Improper oil mixture can destroy
tractor parts.

Avoid entering of dirt into the hydraulic system

The hydraulic system can get seriously damaged. Personal injuries or
material damage can be caused.

Check hoses and couplings

Before connecting, prove all hydraulic hoses for damages. After
connecting check all hydraulic couplings for tight connection.
Defective hydraulic hoses or bad connected hydraulic couplings can
cause injuries or unforeseen movements of the machine.

Secure tractor hydraulic devices

In transport position tractor hydraulic devices must be secured against
unintentional movements. Unintentional movements of the hydraulic
device can cause serious injuries or unforeseen movements of the
machine.

Check correct position of hydraulic hoses

Hydraulic hoses may not stick or tighten. Pay attention to sufficient
free space. Torn or stuck hydraulic hoses cause unverifiable
movements of the machine and serious injuries.

Take care of the correct laying of hydraulic hoses

Hydraulic hoses may not stick or tighten. Take care of sufficient free
space. Worn or stuck hydraulic hoses can cause heavy damage to the
machine or severe injuries.

Check the following connections from the tractor to the machine (if
applicable):

•

hydraulic connections

•

electronic connections

Before coupling, the hydraulic block must be adapted:

•

Hydraulic block - open centre

•

Hydraulic block - closed centre

•

Hydraulic block - load sensing

«
...
31
32
33
34
35
...
»

Содержание RW1600







































































































Отзывы:

Нет отзывов

Похожие инструкции для RW1600

Бренд: Oberheim Страницы: 40

Бренд: Panasonic Страницы: 174

Бренд: Dairyland Страницы: 21

Бренд: HAMAR LASER Страницы: 49

Бренд: Haag-Streit Страницы: 16

ENET-232 Series

Бренд: National Instruments Страницы: 105

Бренд: Omlet Страницы: 2

Бренд: Omicron Страницы: 382

Бренд: Omicron Страницы: 188

Бренд: GE Страницы: 289

Бренд: Össur Страницы: 82

Quadro A Legs 3P 120 Degree Workstation with...

Бренд: Jason.L Страницы: 10

Clinician Premiere Series

Бренд: OAKWORKS Страницы: 29

Бренд: Aeware Страницы: 36

Бренд: Partizzle Страницы: 8

PowerPlant PowerBank+ mk2

Бренд: Harley Benton Страницы: 2

HC-1500 - Type 2E

Бренд: Echo Страницы: 32

Бренд: SafeWaze Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды