background image

- 10 -

The KUHN Mower Conditioner fitted with conditioning rotor complete with free swinging

fingers and adjustable comb has been specially designed for natural grasses but also

gives excellent results when mowing and conditioning grass and clover mixed crops.

KUHN Mower Conditioners fitted with roller conditioners are particularly suitable

for working in lucerne / alfalfa and clover crops.

The instability of the weather makes the preparation of good hay precarious.

Consequently we have designed the KUHN Mower Conditioner to speed the drying cycle

by some 50 % on natural grasses with the subsequent added advantage of reducing to

a minimum the risk period during which the hay is exposed to the vagaries of the

weather.

Making hay by conventional methods needs 3 to 5 days after mowing ; the Kuhn Mower

Conditioner in reasonable weather will reduce the moisture content to 20% in 1 1/

2 to 2 days or it will prepare wilted grass for silage reducing the moisture content

to 60% in 4 to 5 hours.

To obtain the very best hay quality from your crop, you should, after using the Mower

Conditioner, leave the grass for 1 to 2 hours and then use a tedder on it twice.

For example, if cutting took place at 6 or 7.30 am, then it should be tedded at 9.00

am and again at 11.00 am. If this practice is followed, with good weather, the crop

can very often be baled the same evening and the hay will retain the maximum food

value.

Never wait too long before tedding, otherwise the outer layer of hay becomes too dry

with increased losses and the total drying time will be delayed.

Acceleration of the drying process.

INTRODUCTION

Содержание FC 202













































Отзывы: