Kubota LA344 Скачать руководство пользователя страница 68

Страница: 68 / 74

4. Compress the piston seal to the correct size by

installing the piston into the correcting jig (5).

(5) Correcting jig

4.3 Side frames, front guard and

main frames

4.3.1 Removing side frames

1. Remove the pins (2), (5).
2. Remove the side frames (1) from the boom

assembly (3) and the boom cylinder (4).

(1) Side frame
(2) Pin
(3) Boom assembly

(4) Boom cylinder
(5) Pin

4.3.2 Removing front guard

1. Remove the front guard (1).

(1) Front guard

4.3.3 Removing main frames

1. Remove the main frame mounting bolts and nuts

(2) from the tractor body.

2. Remove the main frame (1).

(1) Main frame

(2) Main frame mounting bolt

(When reassembling)

IMPORTANT

• Be careful not to pinch the wire harness when

assembling the main frame.

• Tighten to the specified tightening torque.

Tightening tor-
que

Main frame mount-
ing bolt (M14)

115 N

⋅

11.7 kgf

⋅

85 lbf

⋅

SERVICING

4. Disassembling and assembling

3. FRONT LOADER

LA344, LA344S

3-31

KiSC issued 02, 2017 A

Содержание LA344











































































Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды

Kubota LA344, Руководство по ремонту

Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды