Kubota LA344 Скачать руководство пользователя страница 57

Страница: 57 / 74

• For removing the loader, choose flat and hard

ground, preferably concrete.

• If the ground surface is soft, place suitable

planks on the ground for the bucket and stands.

• When starting the engine or using the hydraulic

control valve, always sit in the operator's seat.

• Make sure the bucket and stands are at ground

level.

4.1.1.1 How to remove the loader

WARNING

• Make sure that an approved bucket is attached

before removing the loader from the tractor.

• For removing the loader, choose flat and hard

ground, preferably concrete.

• If the ground surface is soft, place suitable

planks on the ground for the bucket and the
stand.

• When starting the engine or using the

hydraulic-control-lever, always sit in the
operator's seat.

• Make sure that the bucket and the stand are at

ground level.

1. Set the engine speed to the following speed, and

then raise the boom until the bucket pin is the
height of the boom fulcrum pin.

Engine speed

1800 rpm

2. Dump the bucket fully.

(1) Bucket pin
(2) Boom fulcrum pin

(A) Same height

3. Slide the stand lever downward direction

completely, and release the stand from the stand
hook.

(1) Stand lever
(2) Stand

(3) Stand hook

4. Get the bucket rolled back until its bottom is

positioned the following angle with respect to the
ground surface.

(A) Angle between ground sur-

face and bucket bottom

Angle between ground surface and bucket
bottom (A)

About 20 degrees

3. FRONT LOADER

SERVICING

4.Disassembling and assembling

3-20

LA344, LA344S

KiSC issued 02, 2017 A

Содержание LA344











































































Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды

Kubota LA344, Руководство по ремонту

Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды