Kubota LA344 Скачать руководство пользователя страница 62

Страница: 62 / 74

10. Slowly move the control lever to the

dump

position

until the bucket tilts down as follows.

(1) Bucket
(2) Tip of the stand

(A) Angle between bucket bot-

tom and ground

Angle between bucket bottom and ground (A)

About 20 de-
grees

IMPORTANT

• Make sure that the tips of the stands are off

the ground.

11. Slowly move the hydraulic-control-lever to the

down

position to lift the front wheels slightly with

the loader until the mount hooks are completely
mounted on the main frame as shown in the
following figure.

(1) Mount hook

IMPORTANT

• Make sure that the hooks at both sides are

properly mounted on the main frame.

(1) Wire harness

(2) Side frame

• Make sure not to pinch the wire harness in

the side frame when mounting the third-
function-kit.

12. Slowly move the hydraulic-control-lever to the

position until the cutting edge of the bucket comes
up slightly off the ground.

13. Make sure that the right and left mounting levers

can not be activated.
Do not use the machine if the cutting edge of the
bucket is off the ground but the mount hooks are
unlocked.

(1) Mount hook

(2) Mounting lever

SERVICING

4. Disassembling and assembling

3. FRONT LOADER

LA344, LA344S

3-25

KiSC issued 02, 2017 A

Содержание LA344











































































Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды

Kubota LA344, Руководство по ремонту

Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды