Kubota LA344 Скачать руководство пользователя страница 60

Страница: 60 / 74

• To start the engine and operate the control

valve, always stay in the operator's seat.

4.1.2.1 How to reinstall the loader

WARNING

To avoid personal injury or death:

• When starting the engine and operating the

hydraulic-control-valve, always sit in the
operator's seat.

1. Slowly drive the tractor between the side frames of

the loader until the rear portion of both side frames
touches the main frames as shown in the following
figures.

(1) Side frame
(2) Main frame
[A] LH
[B] RH

(A) 150 mm to 200 mm
(B) Center of side frames

2. Stop the engine and unfasten the seat belt.
3. Remove the protective caps.
4. Connect the quick coupler and lower the lever until

it stops, and then turn the safety-lock-button
clockwise.

(1) Lever
(2) Safety lock button
(A) Lower

(B) Clockwise

IMPORTANT

• Get the quick coupler locked, and move up

and down the lever to make sure that the
quick coupler is tightly locked.

SERVICING

4. Disassembling and assembling

3. FRONT LOADER

LA344, LA344S

3-23

KiSC issued 02, 2017 A

Содержание LA344











































































Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды

Kubota LA344, Руководство по ремонту

Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды