Kubota LA344 Скачать руководство пользователя страница 58

Страница: 58 / 74

5. Lower the boom and raise the front wheels slightly.

IMPORTANT

• When raising the front wheels, the stands

are not to be grounded.

6. Slide the mounting levers of both sides to the

upward direction as shown in the following figure.

(1) Mounting lever

7. Slowly move the hydraulic-control-lever to the

rollback

position to raise the side frames of the

loader up and out of the receivers of the main
frames as shown in the following figure.

(1) Hydraulic control lever

8. Down the mounting levers of both sides as shown

in the following figure.

(1) Mounting lever

9. Back the tractor so that the quick coupler is

positioned at the back of side frame as shown in the
following figure.

(1) Quick coupler

(2) Side frame

10. Stop the engine, and slowly release all hydraulic

pressure by moving the hydraulic-control-lever in all
directions.

11. Unfasten the seat belt, and then turn the safety-

lock-button counterclockwise to unlock it.

(1) Safety lock button

SERVICING

4. Disassembling and assembling

3. FRONT LOADER

LA344, LA344S

3-21

KiSC issued 02, 2017 A

Содержание LA344











































































Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды

Kubota LA344, Руководство по ремонту

Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды