Kubota LA344 Скачать руководство пользователя страница 52

Страница: 52 / 74

10. Lift the stand on the right side of the loader up to

the position shown in the following figure.

(1) Stand hook
(2) Stand pin

(A) Almost the same

11. Reposition the adjusting bolt until it touches the

stand.

(1) Adjusting bolt

NOTE

• The position of the bolt is provisional and

may be roughly set for now.

12. Adjust the adjusting bolt in the same way as for the

stand on the left side of the loader.

13. Position the stand lever as shown in the figure.

(1) Stand lever
(2) Lever guide

(A) Center

14. Turn the adjusting bolt on the right side of the

loader to set the stand pin as shown as follows.

(1) Adjusting bolt
(2) Stand
(3) Stand hook
(4) Stand pin

(A) Almost the same
(B) Adjusting range

Adjusting range (B)

± 15 mm

IMPORTANT

• Be careful not to allow the stands to go

beyond their adjustable range. Otherwise
the stands may get damaged.

15. Lock the stand pin using the lock nut.

SERVICING

3. Checking and adjusting

3. FRONT LOADER

LA344, LA344S

3-15

KiSC issued 02, 2017 A

Содержание LA344











































































Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды

Kubota LA344, Руководство по ремонту

Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды