Kubota D662-E2B Скачать руководство пользователя

Страница: 140 / 142

S-75

SM-E2B SERIES, WSM

DIESEL ENGINE

Field Coil

1. Check the continuity across the lead (1) and brush (2) with a

circuit tester.

2. If it dose not conduct, replace the yoke assembly.
3. Check the continuity across the brush (2) and yoke (3) with a

circuit tester.

4. If it conducts, replace the yoke assembly.

W1156968

(8) Alternator

Bearing

1. Check the bearing for smooth rotation.
2. If it does not rotate smoothly, replace it.

W1019790

Stator

1. Measure the resistance across each lead of the stator coil with

resistance range of circuit tester.

2. If the measurement is not within factory specification, replace it.
3. Check the continuity across each stator coil lead and core with

resistance range of circuit tester.

4. If infinity is not indicated, replace it.

W1019964

Rotor

1. Measure the resistance across the slip rings.
2. If the resistance is not the factory specification, replace it.
3. Check the continuity across the slip ring and core with resistance

range of circuit tester.

4. If infinity is not indicated, replace it.

W1020094

(1) Lead
(2) Bush

(3) Yoke

Resistance

Factory spec.

Less than 1.0

Resistance

Factory spec.

2.9

KiSC issued 06, 2006 A

Содержание D662-E2B















































































































































Результаты поиска

Содержание D662-E2B

Отзывы:

Похожие инструкции для D662-E2B

Бренды по названию

Популярные бренды

Kubota D662-E2B, Руководство по ремонту

Результаты поиска

Содержание D662-E2B

Отзывы:

Похожие инструкции для D662-E2B

Бренды по названию

Популярные бренды