Kubota D662-E2B Скачать руководство пользователя страница 80

Страница: 80 / 142

S-17

SM-E2B SERIES, WSM

DIESEL ENGINE

Thermostat Valve Opening Temperature

1. Suspend the thermostat in the water by a string with its end

inserted between the valve and seat.

2. Heating the water gradually, read the temperature when the

valve opens and leaves the string.

3. Continue heating and read the temperature when the valve

opens approx. 8 mm (0.315 in.).

4. If the measurement is not within the factory specifications,

replace the thermostat.

W1035849

(4) Fuel System

Injection Timing

1. Remove the injection pipes.
2. Remove the engine stop solenoid.
3. Turn the flywheel counterclockwise (viewed from flywheel side)

until the fuel fills up to the hole of the delivery valve holder (3) for
No. 1 cylinder.

4. After the fuel fills up to the hole of the delivery valve holder for No.

1 cylinder, turn back (clockwise) the flywheel around 1.57 rad
(90 °).

5. Turn the flywheel counterclockwise to set at around 0.44 rad

(25 °) before T.D.C..

6. Slowly turn the flywheel counterclockwise and stop turning when

the fuel begins to come up, to get the present injection timing.

7. Check to see the degree on flywheel.

The flywheel has mark “1TC”, “10” and “20” for the crank angle
before the top dead center of No. 1 cylinder.

8. Check to see if the timing angle on the flywheel is aligned with the

alignment mark (2).

9. If injection timing is out of adjustment, readjust the timing with

shims.

Z482/D662/D722-E2B (3600 min

-1

(rpm) spec.)

D782-E2B (3200 min

-1

(rpm) spec.)

Z602/D902-E2B (3200 min

-1

(rpm) spec.)

Z602/D902-E2B (3600 min

-1

(rpm) spec.)

W1018724

Thermostat’s valve
opening temperature

Factory spec.

69.5 to 72.5 °C
157.1 to 162.5 °F

Temperature at which
thermostat completely
opens

Factory spec.

85 °C
185 °F

Injection timing

Factory spec.

0.33 to 0.37 rad (19 to
21 °) before T.D.C.

Injection timing

Factory spec.

0.28 to 0.31 rad (16 to
18 °) before T.D.C.

Injection timing

Factory spec.

0.30 to 0.33 rad (17 to
19 °) before T.D.C.

Injection timing

Factory spec.

0.33 to 0.37 rad (19 to
21 °) before T.D.C.

(1) Timing Line
(2) Alignment Mark
(3) Delivery Valve Holder
(4) Shim (Soft Metal Gasket Shim)

(5) Two-holes : 0.20 mm (0.0079 in.)
(6) One-hole : 0.25 mm (0.0098 in.)
(7) Without hole : 0.30 mm (0.0118 in.)

KiSC issued 06, 2006 A

Содержание D662-E2B















































































































































Результаты поиска

Содержание D662-E2B

Отзывы:

Похожие инструкции для D662-E2B

Бренды по названию

Популярные бренды

Kubota D662-E2B, Руководство по ремонту

Результаты поиска

Содержание D662-E2B

Отзывы:

Похожие инструкции для D662-E2B

Бренды по названию

Популярные бренды