Kubota D662-E2B Скачать руководство пользователя страница 30

Страница: 30 / 142

G-8

SM-E2B SERIES, WSM

G GENERAL

[2] CHECK POINTS OF INITIAL 50 HOURS

Changing Engine Oil

CAUTION

• Be sure to stop engine before changing engine oil.

1. Start and warm up the engine for approx. 5 minutes.
2. Place an oil pan underneath the engine.
3. To drain the used oil, remove the drain plug (2) at the bottom of

the engine and drain the oil completely.

4. Screw the drain plug (2).
5. Fill new oil up to upper line on the dipstick (1).

IMPORTANT

■

• When using an oil of different maker or viscosity from the

previous one, remove all of the old oil.

• Never mix two different types of oil.
• Engine oil should have properties of API classification CD/

CE/CF/CF-4/CG-4.

• Use the proper SAE Engine Oil according to ambient

temperature.

• Upon an oil change, be sure to replace the gasket with new

one.

* 101 mm (3.98 in.) oil pan depth is optional.

W1016604

Above 25 °C (77 °F)

SAE 30 or SAE 10W-30
SAE 10W-40

0 °C to 25 °C (32 °F to 77 °F)

SAE 20 or SAE 10W-30
SAE 10W-40

Below 0 °C (32 °F)

SAE 10W or SAE 10W-30
SAE 10W-40

Oil pan depth

Models

Engine oil capacity

101 mm (3.98 in.)

121 mm (4.76 in.)

*Z482-E2B

2.1 L

0.55 U.S.gals

2.5 L

0.66 U.S.gals

*D662-E2B
*D722-E2B

3.2 L

0.85 U.S.gals

3.8 L

1.00 U.S.gals

D782-E2B

–

3.6 L

0.95 U.S.gals

Z602-E2B

2.5 L

0.66 U.S.gals

–

D902-E2B

3.7 L

0.98 U.S.gals

–

Tightening
torque

Drain plug with
copper gasket

M12

1.25

32.4 to 37.3 N·m
3.3 to 3.8 kgf·m
23.9 to 27.5 ft-lbs

M22

1.5

63.7 to 73.5 N·m
6.5 to 7.5 kgf·m
47.0 to 54.2 ft-lbs

Drain plug with
rubber coated
gasket

M22

1.5

44.1 to 53.9 N·m
4.5 to 5.5 kgf·m
32.5 to 39.8 ft-lbs

(1) Dipstick

(2) Drain Plug

KiSC issued 06, 2006 A

Содержание D662-E2B















































































































































Результаты поиска

Содержание D662-E2B

Отзывы:

Похожие инструкции для D662-E2B

Бренды по названию

Популярные бренды

Kubota D662-E2B, Руководство по ремонту

Результаты поиска

Содержание D662-E2B

Отзывы:

Похожие инструкции для D662-E2B

Бренды по названию

Популярные бренды