Kubota D662-E2B Скачать руководство пользователя

Страница: 92 / 142

S-29

SM-E2B SERIES, WSM

DIESEL ENGINE

(2) External Components

Alternator, Starter and Others

1. Remove the air cleaner and muffler.
2. Remove the engine stop solenoid (1).
3. Remove the cooling fan (2), fan pulley and fan belt (3).
4. Remove the alternator.
5. Remove the starter.
(When reassembling)

• Check to see that there are no cracks on the belt surface.

IMPORTANT

■

• Keep the engine stop lever (7) to touch the stopper (6).

Tighten the engine stop solenoid mounting screw (4) so that
there be no gap between the engine stop lever and the
engine stop solenoid plunger (5).

• After reassembling the fan belt, be sure to adjust the fan belt

tension.

• Do not confuse the direction of the fan.

W1023769

(3) Cylinder Head, Valves and Oil Pan

Cylinder Head Cover

1. Disconnect the breather hose (1).
2. Remove the cylinder head cover screws (2).
3. Remove the cylinder head cover (3).
(When reassembling)

• Check to see if the cylinder head cover gasket is not defective.

W1028468

Injection Pipes

1. Loosen the screws to the pipe clamp (2).
2. Detach the injection pipes (1).
(When reassembling)

• Sent compressed air into the pipes to blow out dust. Then,

reassemble the pipes in the reverse order.

W1028640

(1) Engine Stop Solenoid
(2) Cooling Fan
(3) Fan Belt
(4) Engine Stop Solenoid Mounting

Screw

(5) Plunger

(6) Stopper
(7) Engine Stop Lever

A : 0 mm (0 in.)

Tightening torque

Cylinder head cover screw

6.86 to 11.3 N·m
0.7 to 1.15 kgf·m
5.1 to 8.3 ft-lbs

(1) Breather Hose
(2) Cylinder Head Cover Screws

(3) Cylinder Head Cover

Tightening torque

Injection pipe retaining nut

24.5 to 34.3 N·m
2.5 to 3.5 kgf·m
18.1 to 25.3 ft-lbs

(1) Injection Pipe

(2) Pipe Clamp

KiSC issued 06, 2006 A

Содержание D662-E2B















































































































































Результаты поиска

Содержание D662-E2B

Отзывы:

Похожие инструкции для D662-E2B

Бренды по названию

Популярные бренды

Kubota D662-E2B, Руководство по ремонту

Результаты поиска

Содержание D662-E2B

Отзывы:

Похожие инструкции для D662-E2B

Бренды по названию

Популярные бренды