KTM RC 390 Скачать руководство пользователя

Страница: 90 / 200

SERVICE WORK ON THE CHASSIS

L02150-10

Main work

–

Loosen nut



–

Loosen nuts



–

Adjust the chain tension by turning adjusting screws



on the left and right.

Guideline

Chain tension

5… 7 mm (0.2… 0.28 in)

Turn the adjusting screws



on the left and right so that the markings on the

left and right chain adjusters



are in the same position relative to the reference

marks



. The rear wheel is then correctly aligned.

Info

The upper chain section must be taut.
Chain wear is not always even, so you should check the setting at different chain
positions.

–

Tighten nuts



–

Make sure that chain adjusters



are fitted correctly on adjusting screws



–

Tighten nut



Guideline

Nut, rear wheel spindle

M14x1.5

90 Nm
(66.4 lbf ft)

Содержание RC 390









































































































































































































Результаты поиска

Содержание RC 390

Отзывы:

Похожие инструкции для RC 390

Бренды по названию

Популярные бренды

KTM RC 390, Руководство пользователя

Результаты поиска

Содержание RC 390

Отзывы:

Похожие инструкции для RC 390

Бренды по названию

Популярные бренды