KTM RC 390 страница 134 Скачать руководство пользователя

Страница: 134 / 200

ELECTRICAL SYSTEM

132

15.6

Changing the low beam bulb

Note

Damage to reflector

Reduced brightness.

–

Grease on the lamp will evaporate due to the heat and be deposited on the reflector. Clean the lamp and keep it free of grease before
mounting.

Preparatory work

–

Switch off all power consumers and switch off the engine.

L02161-10

Main work

–

Turn socket



counterclockwise.

–

Pull the socket with low beam bulb



out of the headlight housing.

–

Disconnect the socket with the low beam bulb from connector



and remove.

–

Connect the new socket with the low beam bulb to the connector.

Low beam (H11 / Sockel PGJ19-2) (

p. 177)

Содержание RC 390









































































































































































































Результаты поиска

Содержание RC 390

Отзывы:

Похожие инструкции для RC 390

Бренды по названию

Популярные бренды

KTM RC 390, Руководство пользователя

Результаты поиска

Содержание RC 390

Отзывы:

Похожие инструкции для RC 390

Бренды по названию

Популярные бренды