KTM RC 390 страница 151 Скачать руководство пользователя

Страница: 151 / 200

TUNING THE ENGINE

149

17.2

Adjusting the play in the throttle cable

M00452-10

–

Move the handlebar to the straight-ahead position.

–

Push back sleeve



–

Loosen lock nut



–

Adjust the play in the throttle cable by turning adjusting screw



Guideline

Throttle cable play

3… 5 mm (0.12… 0.2 in)

–

Tighten lock nut



–

Slide on sleeve



17.3

Checking the clutch lever play

L02111-11

–

Check the clutch lever for smooth operation.

–

Move the handlebar to the straight-ahead position. Pull the clutch lever until resistance
is perceptible, and determine the play in the clutch lever



Clutch lever play

1… 3 mm (0.04… 0.12 in)

» If the clutch lever play does not meet specifications:

–

Adjust the clutch cable play.

(

p. 150)

Note

Clutch damage

If there is no play on the clutch lever, the clutch will begin to slip.

–

Before operating the motorcycle, always check the clutch lever play.

–

Move the handlebar to and fro over the entire steering range.

The clutch lever play must not change.

Содержание RC 390









































































































































































































Результаты поиска

Содержание RC 390

Отзывы:

Похожие инструкции для RC 390

Бренды по названию

Популярные бренды

KTM RC 390, Руководство пользователя

Результаты поиска

Содержание RC 390

Отзывы:

Похожие инструкции для RC 390

Бренды по названию

Популярные бренды