KTM 990 Adventure AUS Скачать руководство пользователя

Страница: 175 / 218

TROUBLESHOOTING

173

Faults

Possible cause

Action

The engine does not turn when the
starter button is pressed

Operating error

–

Carry out the start procedure. (

p. 50)

Battery discharged

–

Recharge the battery.

(

p. 124)

–

Check the closed current.

IGNITION, FUEL PUMP

, or

POWER RELAY

fuse blown

–

Change the fuses in the fuse box. (

p. 130)

Main fuse burned out

–

Change the main fuse. (

p. 126)

Ignition/steering lock or emergency
OFF switch defective

–

Check the emergency OFF switch.

–

Check the ignition/steering lock.

Defect in safety start system

–

Check the safety start system.

Immobilizer control unit not activated

–

Activate the immobilizer control unit.

Malfunction in CAN bus communica-
tion

–

Check the CAN bus communication.

Combination instrument defective

–

Check the combination instrument.

Control unit for electric start lock
defective

–

Check the control unit of the electric start
lock.

Engine turns only if the clutch lever is
drawn

The vehicle is in gear

–

Shift the transmission to neutral.

Defect in safety start system

–

Check the safety start system.

Engine turns although a gear is
engaged

Defect in safety start system

–

Check the safety start system.

Engine turns but does not start

Coupling of fuel hose connection not
connected

–

Reconnect coupling of fuel hose connection.

Socket connector of wiring harness
oxidized

–

Clean the socket connector and treat it with con-
tact spray.

Defect in fuel injection system

–

Read out the fault memory using the KTM diag-
nostics tool.

Содержание 990 Adventure AUS



























































































































































































































Результаты поиска

Содержание 990 Adventure AUS

Отзывы:

Похожие инструкции для 990 Adventure AUS

Бренды по названию

Популярные бренды

KTM 990 Adventure AUS, Руководство пользователя

Результаты поиска

Содержание 990 Adventure AUS

Отзывы:

Похожие инструкции для 990 Adventure AUS

Бренды по названию

Популярные бренды