KTM 990 Adventure AUS Скачать руководство пользователя страница 138

Страница: 138 / 218

ELECTRICAL SYSTEM

136

100594-10

–

Remove rubber cap



and disconnect plug-in connector



100595-10

–

Detach spring bar



and remove the bulb from the headlight.

–

Position the new bulb in the headlight and attach the spring bar.

High beam (H3 / socket PK22s) (

p. 192)

Info

The bulb must be correctly seated at projections



–

Connect the plug-in connector and mount the rubber cap.

–

Install the headlight mask with the headlight. (

p. 134)

13.11

Changing the parking light bulb in the headlight

Note

Damage to reflector

Reduced luminance.

–

Grease on the lamp will evaporate due to the heat and be deposited on the reflector. Clean the lamp and keep it free of grease before
mounting.

–

Remove the headlight mask with the headlight. (

p. 132)

Содержание 990 Adventure AUS



























































































































































































































Результаты поиска

Содержание 990 Adventure AUS

Отзывы:

KTM 990 Adventure AUS, Руководство пользователя, Страница: 138 / 218

Результаты поиска

Содержание 990 Adventure AUS

Отзывы: