KTM 990 Adventure AUS Скачать руководство пользователя страница 137

Страница: 137 / 218

ELECTRICAL SYSTEM

135

100592-10

–

Remove rubber cap



and connector



from the bulb.

100593-10

–

Detach spring bar



and remove the bulb from the headlight.

–

Position the new bulb in the headlight and attach the spring bar.

Low beam (H7 / socket PX26d) (

p. 192)

Info

The bulb must be positioned with projection



in the recess.

–

Attach the connector to the bulb and mount the rubber cap.

–

Install the headlight mask with the headlight. (

p. 134)

13.10

Changing the high beam bulb

Note

Damage to reflector

Reduced luminance.

–

Grease on the lamp will evaporate due to the heat and be deposited on the reflector. Clean the lamp and keep it free of grease before
mounting.

–

Remove the headlight mask with the headlight. (

p. 132)

Содержание 990 Adventure AUS



























































































































































































































Результаты поиска

Содержание 990 Adventure AUS

Отзывы:

KTM 990 Adventure AUS, Руководство пользователя, Страница: 137 / 218

Результаты поиска

Содержание 990 Adventure AUS

Отзывы: