KTM 990 Adventure AUS Скачать руководство пользователя страница 126 | Manualshive

Страница: 126 / 218

KTM 990 Adventure AUS Скачать руководство пользователя страница 126

ELECTRICAL SYSTEM

124

100579-11

–

Hook cover



into the battery compartment at the bottom and swing up.

–

Mount and tighten screws



.

–

Install the underride guard.

–

Set the clock. (

13.3

Recharging the battery

x

Warning

Risk of injury

Battery acid and battery gases cause serious cauterization.

–

Keep batteries out of the reach of children.

–

Wear suitable protective clothing and goggles.

–

Avoid contact with battery acid and battery gases.

–

Keep the battery away from sparks or open fire. Charge only in well ventilated rooms.

–

Flush with copious amounts of water in case of skin contact. If battery acid comes into contact with the eyes, flush the eyes
with water for at least 15 minutes and consult a physician.

Warning

Environmental hazard

Battery parts and acid are harmful to the environment.

–

Do not discard batteries with the household trash. Dispose of a defective battery in an environmentally compatible manner.
Give the battery to your KTM dealer or to a recycling center that accepts used batteries.

«
...
124
125
126
127
128
...
»

Содержание 990 Adventure AUS



























































































































































































































Отзывы:

Нет отзывов