KTM 990 Adventure AUS Скачать руководство пользователя страница 170 | Manualshive

Страница: 170 / 218

KTM 990 Adventure AUS Скачать руководство пользователя страница 170

CLEANING, CARE

168

17.1

Cleaning motorcycle

Note

Material damage

Damage and destruction of components by high-pressure cleaning equipment.

–

Never clean the vehicle with high-pressure cleaning equipment or a strong water-jet. The excessive pressure can penetrate electrical
components, socket connects, throttle cables, and bearings, etc., and can damage or destroy these parts.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Info

If you clean the motorcycle regularly, its value and appearance are maintained over a long period.
Avoid direct sunshine on the motorcycle during cleaning.

401061-01

–

Close off the exhaust system to keep water from entering.

–

First remove coarse dirt particles with a gentle water spray.

–

Spray very dirty areas with a normal motorcycle cleaner and then clean with a paint-
brush.

Motorcycle cleaner (

Info

Clean the vehicle using warm water containing normal motorcycle cleaner and a
soft sponge.
If the vehicle was operated in road salt, clean it with cold water. Warm water
would enhance the corrosive effects of salt.

«
...
168
169
170
171
172
...
»

Содержание 990 Adventure AUS



























































































































































































































Отзывы:

Нет отзывов