KTM 990 Adventure AUS Скачать руководство пользователя страница 165

Страница: 165 / 218

SERVICE WORK ON THE ENGINE

163

100629-10

–

Mount oil drain plug



with the magnet and new seal ring and tighten.

Guideline

Oil drain plug with magnet

M22x1.5

35 Nm
(25.8 lbf ft)

–

Slide oil sieve



into the engine case with the

TOP

marking facing up.

–

Check the form ring in cover



for damage and correct seating.

–

Position cover



. Mount and tighten the screws.

Guideline

Screw, clutch cover

10 Nm (7.4 lbf ft)

100625-10

–

Position bracket



. Mount and tighten screws



Guideline

Remaining chassis screws

25 Nm
(18.4 lbf ft)

–

Mount and tighten screw



on the right fuel tank.

Guideline

Screw, fuel tank

15 Nm
(11.1 lbf ft)

16.4

Removing the oil filter

Warning

Danger of scalding

Engine oil and gear oil get very hot when the motorcycle is ridden.

–

Wear appropriate protective clothing and safety gloves. In case of burns, rinse immediately with lukewarm water.

Содержание 990 Adventure AUS



























































































































































































































Результаты поиска

Содержание 990 Adventure AUS

Отзывы:

KTM 990 Adventure AUS, Руководство пользователя, Страница: 165 / 218

Результаты поиска

Содержание 990 Adventure AUS

Отзывы: