KSR Ride Speedy Скачать руководство пользователя страница 32

Страница: 32 / 79

BRAKES

BRAKE OPERATION INSPECTION REAR

1. Operate the left hand brake lever until the brake pads lie on

the brake drum and check if there is a pressure point. If there

is no pressure point check the brake system.

2. While operate the rear brake lever push the vehicle forward

and backward on the handlebar to check if the brake system

is working. If the brake do not work correct check the brake

system.

3. Final make a driving test with low speed and check if the

brake system is working. If the brake do not work correct

check the brake system.

REAR BRAKE SYSTEM ADJUSTMENT

The rear brake system is operated by a steel cable. By adjusting

the steel cable, the brake can be set.

1. Operate the left hand brake lever until the brake pads lie down

on the brake drum.

The free play (A)

between the 0 position

and the pressure point must be

10 to 20 mm.

When free play

is higher or lower the brake cable need to adjusted.

2. To adjust the brake cable turn the adjustment nut (1) in or out

till the free play of the brake lever is ok.

Please consider that the rear brake system must not block when

operating. The rear brake is a support brake. The main brake

system is the front brake system. The brake ration between front

brake and rear brake is 80:20.

If you can not adjust the free play correct check the brake pads

and the brake cable for wear.

BRAKE CABLE REPLACEMENT

When the brake cable is worn or broken replace it.

1. For an easy replacement of the brake cable you must remove

the front handlebar cover (2), front middle cover (3) and the

leg protection panel/floor panel (4).

2. Release the adjustment nut (1) and move the cable forward.

3. Release it from the left brake lever.

4. Before you install the replacement cable grease it with multi

purpose lubricant.

5. Install the replacement cable in reversed order. Take care that

also the tension spring (5) between the stop and the linkage

(6) is installed correct and the cable is placed in all brackets.

6. Adjust the brake cable and install the cover parts.

NOTE

Содержание Ride Speedy
















































































Результаты поиска

Содержание Ride Speedy

Отзывы:

Похожие инструкции для Ride Speedy

Бренды по названию

Популярные бренды

KSR Ride Speedy, Руководство по ремонту

Результаты поиска

Содержание Ride Speedy

Отзывы:

Похожие инструкции для Ride Speedy

Бренды по названию

Популярные бренды