KSR Ride Speedy Скачать руководство пользователя страница 68

Страница: 68 / 79

ELECTRICAL SYSTEM/ CABLES

• Loose cable is a hidden trouble to electrical safety.

After clamped check each cable to ensure electrical
safety.

• It is not allowed to leave any wire clip bending

towards bonding points.

• Bind each cable to its designated position.
• It is not allowed to lay a cable to end or a sharp

corner on frame.

• It is not allowed to lay a cable to end of a bolt or

screw.

• When laying a cable, keep it away from any heat

source or any place where may bite it when it is
moving.

• When laying a cable along a handle, avoid it being

strained too tightly or loosely and it can not interfere
with any adjacent part at any turning point.

• All cables should be laid smoothly without twist or

knot.

• Before butt-jointing a connector,check if its sheath

has been damaged and if it is overstretched.

• If a cable is at a sharp corner or outer corner, use

tape or hose to protect it.

• After a cable is repaired, use tape to bind it securely.
• Keep all control cables from bend or twist because

dumb control will result in case any control cable is
damaged.

NOTE

O: CORRECT
X: INCORRECT

Содержание Ride Speedy
















































































Результаты поиска

Содержание Ride Speedy

Отзывы:

Похожие инструкции для Ride Speedy

Бренды по названию

Популярные бренды

KSR Ride Speedy, Руководство по ремонту

Результаты поиска

Содержание Ride Speedy

Отзывы:

Похожие инструкции для Ride Speedy

Бренды по названию

Популярные бренды