KSR Ride Speedy Скачать руководство пользователя страница 45

Страница: 45 / 79

BRAKES

BRAKE PAD WEAR INSPECTION

Reduced braking efficiency caused by worn brake pads.
Change worn brake pads immediately. Always replace the brake
pads in pair.

Front: See page:29
Rear: See page: 30

BRAKE DISC INSPECTION

Check the thickness of the front disc (1) at several places on the
Disc to see if it confirms to measurement.
See page: 30

BRAKE DRUM INSPECTION

Check the inner diameter of the brake drum (1) at several
places on the drum to see if it confirms to measurement.
See page: 31

BRAKE FLUID

△

！

WARNING

1. Never use dirty or unspecified brake fluid or mix different

Brake fluid because it will damage the brake system.

2. Brake fluid spilled on brake pads or brake disk will reduce

the braking effect. Clean the brake pads and brake disk
with a high quality brake degreaser.

3. When servicing the brake system, use shop towels to cover

plastic parts and coated surfaces to avoid damage caused by
splash of brake fluid.

4. Do not allow dust or water to enter the brake system during

refilling.

Brake fluid should be replaced at least every 2 years.

SPECIFICATION - FRONT BRAKE

Brake fluid type

CASTROL SUPER DISK BRAK E FLUID DOT 4

Brake fluid boiling temperature

> 170 °C

Brake fluid water content

<3%

Содержание Ride Speedy
















































































Результаты поиска

Содержание Ride Speedy

Отзывы:

Похожие инструкции для Ride Speedy

Бренды по названию

Популярные бренды

KSR Ride Speedy, Руководство по ремонту

Результаты поиска

Содержание Ride Speedy

Отзывы:

Похожие инструкции для Ride Speedy

Бренды по названию

Популярные бренды