manualshive.com logo in svg

Krendl 500, Руководство пользователя, Страница: 5 / 59

Поделиться
Скачать
Krendl 500 Скачать руководство пользователя страница 5

Rev. Date: 3/14/18

Page 2

MODEL #500

GENERAL  SAFETY INFORMATION

Important:  

Read 

all

 instructions 

before

 operating this unit.  This equipment can be potentially

dangerous and must be used in strict accordance with instructions.

Disclaimer Notice:  

The manufacturer will not be legally responsible for any injury or damage resulting

from the improper use of this equipment or the failure to follow instructions.

Unpacking

Handle cartons with care to avoid damage from dropping or bumping.  Store and  unpack cartons with the
correct side up.  Completely remove machine from the packaging and from any shipping pallet or skid to
which it might be attached.  In addition, completely remove all shipping materials from 

inside

 the machine.

General Safety

1. Read this manual carefully and become familiar with your machine unit.  Know its applications,

limitations, and any hazards involved.

2. This machine was designed and manufactured for specific applications.  Do not attempt to

modify the unit or use it for any application it was not designed for.  If you have any questions
about your intended use or the machines suitability, ask your dealer/distributor or consult the
factory.  The manufacturers' could not possibly anticipate every circumstance that might involve
a hazard.  For that reason, warnings in the manual and warning tags or decals affixed to the unit,
are 

not

 all-inclusive.  If you intend to handle, operate, or service the unit by a procedure or method

not specifically recommended by the manufacturer, first make sure that such a procedure or
method will not render this equipment unsafe or pose a threat to you and others.

Electrical Safety

•

The 

National Electric Code 

(NEC) in the United States and many international electrical codes require

frame and external electrically conductive parts of this machine to be properly connected to an approved
earth ground.  Local electrical codes may also require proper grounding of machine.  Consult with local
electricians for grounding requirements in your area.

• Never handle any kind of electrical cord or device while standing in water, while barefoot or while hands

or feet are wet.  Dangerous electrical shock will result.

• Use a ground fault circuit interrupter (GFCI) in any damp or highly conductive area. (metal decking or steel work)

• Reference NFPA 79, 70E, or OSHA safe work practices when performing energized work procedures.

Содержание 500




























































Отзывы:

Нет отзывов