manualshive.com logo in svg

Krendl 500, Руководство пользователя, Страница: 34 / 59

Поделиться
Скачать
Krendl 500 Скачать руководство пользователя страница 34

Rev. Date: 3/14/18

Page 31

MODEL #500

Problem

1) Voltmeter showing no voltage 

or

 low voltage.

Electrical Troubleshooting

IMPORTANT

Whenever power is interrupted to unit (i.e., unplugged, main disconnect switch off, kill switch
depressed), power must be restored by correcting power interruption condition and pressing

 green

start button.

Corrective Action

A. Turn Main Disconnect Switch to ON position.
B. Check input cord(s) for proper connection to power source.
C. Check power source for proper voltage.
D. Open Main Control Box lid and check voltage with multitester

at voltmeter terminals.  Replace defective voltmeter.

E. On single input, 240volt/60hz. units, check for proper wiring

of four prong plug and connector body.

A. Check voltmeter.  If no voltage, refer to #1 above.
B. Check power on 

both

 input cords. (double input machines)

C. Check indicator tab on the top of the dropout relay. If tab is

out, relay is not engaged.  If tab is in, relay is engaged.  On
double input machines, check the dropout relay on the top
(C3). (If tab is "in", refer to #3.)

A. Check transformer breaker (breaker#1) (Green, breaker is

tripped.  Red breaker is OK.)

B. Check secondary output of transformer (24volt).  Replace if

necessary

A. Check for proper start-up conditions as mentioned at

beginning of this section.  (See #2)

B. Be sure remote control cord is properly plugged into Main

Control Box.

C. Check remote control cord and hand pendant switch for

damage or loose connections.

D. If neither Remote mode or Manual mode will function, check

transformer breaker (breaker#1) (Green, breaker is tripped.
Red breaker is OK.)

A. Check operation in remote mode and manual mode with 4-

Position Selector Switch and remote hand pendant.

B. Check blower control for ON position.
C. Check for defective, broken, or loose wiring connections

inside Main Control Panel.

D. Check blower motor.  Disconnect  power supply and visually

inspect system for defective, broken or loose wiring connec-
tions inside blower box.

E. Check blower breaker(s) in Main Control Panel.  (Green,

breaker is tripped.  Red breaker is OK.)

F. Check Blower Controls.  Disconnect Blower Control wires

on Main Control Panel door and reconnect the two power
leads bypassing the Blower Control.  (Blower will run full
speed only.)

G. Visually inspect and/or replace blower relay (C5) inside

Main Control Panel.

2) Dropout relay 

does not

 engage.

3) Dropout relay 

is

 engaged (tab is "in"), but machine will not

run.

4) Machine does not function with hand pendant while 4-

Position Selector Switch is in REMOTE mode.

5) Blower  motor does not run, but agitator motor does run.

Содержание 500




























































Отзывы:

Нет отзывов