kozy heat PRINCETON RPC-36 Скачать руководство пользователя страница 1

DIRECT VENT FIREPLACE 

WARNING

:  This product must be installed by 

a licensed plumber or gas fitter when installed 

in the Commonwealth of Massachusetts. 

 
IMPORTANT: Installation of a CO detector is 

required in the fireplace room when installed in 

the Commonwealth of Massachusetts. 

 

  

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or          

 

    any other appliance. 

 

 IF YOU SMELL GAS: 

 

  Do not light any appliance. 

 

  Do not touch any electrical switch: do not use any phone in your building. 

 

  Immediately call gas supplier from a neighbors phone.  Follow the gas supplier instructions. 

 

  If you cannot reach your gas supplier, call the fire department. 

      

  Installation and service must be performed by a qualified installer, service agency or the gas 

           

 

     

supplier.

 

WARNING:  

If the information in these instructions are not followed exactly, a fire or  

explosion  may result, causing property damage, personal injury or loss of life. 

This appliance may be installed in an aftermarket permanently located, manufactured (mobile) home, 
where not prohibited by local codes. 

This appliance is only for use with the type (s) of gas indicated on 
the rating plate. A conversion kit is supplied with the appliance. 

www.kozyheat.com 

INSTALLATION  

AND  

OPERATION MANUAL 

Quality Fireplaces for Life 

DO 

NO

T  

DISC

ARD

 

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE. 
 
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

 

April 2009 

PRC-04-09-R06 

Содержание PRINCETON RPC-36































































Отзывы: