Kontron ETX Component SBC C3 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 64

background image

Kontron

Appendix C: BIOS Operation

30

ETX-P3/C3 User’s Guide

14.

APPENDIX C: BIOS OPERATION

The module is equipped with a Phoenix BIOS, which is located in an onboard Flash EEPROM.

The device has 8-bit access. Faster access (16 bit) is provided by the shadow RAM feature.
You can update the BIOS using a Flash utility.

14.1

Determining the BIOS Version

To determine the PhoenixBIOS version, immediately press the Pause key on your keyboard

as soon as you see the following text display in the upper left corner of your screen:

PhoenixBIOS 4.0 Release 6.0

Copyright 1985-2001 Phoenix Technology Ltd.

All Rights Reserved

Kontron® BIOS Version <MOD6R124>

© Copyright 2003 Kontron Embedded Modules GmbH

14.2

Setup Guide

The PhoenixBIOS Setup Utility changes system behavior by modifying the BIOS
configuration. The setup program uses a number of menus to make changes and turn

features on or off.

The BIOS setup menus documented in this section represent those found in most models of

the

ETX-P3/C3.

The BIOS Setup for specific models can differ slightly.

Note

: Selecting incorrect values may cause system boot failure. Load setup-default values to recover by pressing

<F9>. It might also be necessary to use the “reset configuration data” option in the BIOS setup and set it to
“yes”. In certain circumstances this may also help to recover from system boot failure or a resource conflict.

14.2.1.

Start Phoenix BIOS Setup Utility

To start the PhoenixBIOS setup utility, press <

F2

> when the following string appears during

bootup.

Press <F2> to enter Setup

The Main Menu then appears.

«
...
34
35
36
37
38
...
»

Содержание ETX Component SBC C3

































































Отзывы:

Нет отзывов

Похожие инструкции для ETX Component SBC C3

Бренд: Advantech Страницы: 3

Бренд: Ublox Страницы: 21

DLP LightCrafter Display 3310

Бренд: Texas Instruments Страницы: 16

7001G - VIA Mini ITX Motherboard

Бренд: VIA Technologies Страницы: 76

DQ963FX - Desktop Board Motherboard

Бренд: Intel Страницы: 72

Бренд: Microchip Technology Страницы: 34

Бренд: Parker Страницы: 56

Бренд: EPC Страницы: 10

Бренд: Gigabyte Страницы: 52

Бренд: Acorp Страницы: 54

Бренд: Gigabyte Страницы: 96

MBD-X11SDV-4C-TP8F-B

Бренд: Supermicro Страницы: 123

STEVAL-IHM011V1

Бренд: ST Страницы: 27

EVAL-AD4696FMCZ

Бренд: Analog Devices Страницы: 28

Бренд: ASROCK Страницы: 282

Бренд: Abit Страницы: 96

Бренд: ASROCK Страницы: 173

Бренд: ASROCK Страницы: 216

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды