Kontron ETX Component SBC C3 Скачать руководство пользователя страница 44

Страница: 44 / 64

Kontron

Appendix C: BIOS Operation

ETX-P3/C3 User’s Guide

14.4.6.

I/O Device Configuration Submenu

Feature

Option

Description

Local bus IDE adapter

Disabled
Primary
Secondary

Both

Enables onboard PCI IDE device.

*Onboard FDC

Disabled

Enabled

Enables onboard FDC controller.

External FDC

Disabled

Enabled
Auto

Enables FDC controller on the backplane.

Base I/O address

Primary

Secondary

Selects base address of the FDC controller. (Primary =
3F0h, Secondary = 370)

Serial Port A
Serial Port B

Disabled
Enabled

Auto

Disabled turns off port.
Enabled requires end user to enter the base I/O address
and the IRQ.
Auto makes the BIOS configure the port.
OS Controlled lets the PNP OS configure the port after
bootup.

Mode

Normal

IrDA
ASK-IR

Sets mode of Serial Port B.

Serial Port C
Serial Port D

Disabled

Enabled
Auto

Disabled turns off port.
Enabled requires end user to enter base I/O address and
IRQ.
Auto makes BIOS configure the port.

Mode

Normal

IrDA
ASK-IR

Sets mode for Serial Port D.

IrDA Pins

Standard

Alternate

Selects which pins of the SMC669 to use for the IrDA
interface.

Base I/O address

3F8h, 2F8h,
3E8h, 2E8h

Select I/O base of port.

IRQ (Port A and B)

IRQ 3, IRQ 4

Select IRQ of Port A and B.

IRQ (Port C and D)

IRQ 10, IRQ 11

Select IRQ of Port C and D.

*Onboard LPT

Disabled
Enabled

Auto

Disabled turns off the port.
Enabled requires end user to enter base I/O address and
IRQ.
Auto makes BIOS configure port.

*Mode

Output only

Bi-directional

ECP
EPP

Sets mode for parallel port.

*Base I/O address

378h

, 278h,

3BCh

Select I/O base of port.

*IRQ

IRQ 5,

IRQ 7

Select IRQ of parallel port.

*DMA

DMA1,

DMA3

Select DMA channel of port if in ECP mode.

External LPT

Disabled

Enabled

Disabled turns off the port.
Enabled requires end user to enter the base I/O address
and the IRQ.

Mode

Output only

Bi-directional

EPP

Set the mode for the Parallel Port 2.
Note: ECP is not supported on LPT2

Содержание ETX Component SBC C3

































































Результаты поиска

Содержание ETX Component SBC C3

Отзывы:

Бренды по названию

Популярные бренды

Kontron ETX Component SBC C3, Руководство пользователя

Результаты поиска

Содержание ETX Component SBC C3

Отзывы:

Бренды по названию

Популярные бренды