Kontron ETX Component SBC C3 Скачать руководство пользователя страница 51

Страница: 51 / 64

Kontron

ETX-P3/C3 User’s Guide

Appendix C: BIOS Operation

14.8.6.

Boot First Menu

Display the

Boot First Menu

by pressing <

Esc

> during POST. In response, the BIOS displays

the message

Entering Boot Menu

and then displays the Boot Menu at the end of POST.

Use the menu to select a following option:

Override the existing boot sequence (for this boot only) by selecting another boot

device. If the specified device does not load the OS, the BIOS reverts to the previous
boot sequence.

Enter Setup.

Press <

Esc

> to continue with the existing boot sequence.

14.9

Exit Menu

The following sections describe the five options in

Exit Menu

. Pressing <

Esc

> does not exit

this menu. You must select an item from the menu to exit.

Exit Saving Changes

Saves all selections and exits setup. Upon reboot, the BIOS configures the system
according to the Setup selection stored in CMOS.

Exit Discarding Changes

Use this option to exit Setup without storing new selections in CMOS. Previous selections

remain in effect.

Load Setup Defaults

Select to display the default values for all Setup menus.

Discard Changes

Discards changes made during a Setup session and reverts to values previously saved in
CMOS.

Save Changes

Saves all selections without exiting Setup.

14.10

Updating or Restoring BIOS

Phoenix Phlash allows you to update or restore the BIOS by using a floppy disk without
having to install a new ROM chip.

Содержание ETX Component SBC C3

































































Результаты поиска

Содержание ETX Component SBC C3

Отзывы:

Похожие инструкции для ETX Component SBC C3

Бренды по названию

Популярные бренды

Kontron ETX Component SBC C3, Руководство пользователя

Результаты поиска

Содержание ETX Component SBC C3

Отзывы:

Похожие инструкции для ETX Component SBC C3

Бренды по названию

Популярные бренды