Kontron ETX Component SBC C3 Скачать руководство пользователя страница 26

Страница: 26 / 64

Kontron

Connector X4 Subsystems

ETX-P3/C3 User’s Guide

9.3

Power Control

9.3.1.

Power Good / Reset Input

The

ETX-P3/C3

provides an external input for a power good signal or a manual reset

pushbutton. The implementation of this subsystem complies with the

ETX Specification

Implementation information is provided in the

ETX Design Guide

. Refer to those documents

for additional information.

9.4

Power Management

9.4.1.

ATX PS Control

The

ETX-P3/C3

can control the main power output of an ATX-style power supply. The

implementation of this subsystem complies with the

ETX Specification

. Implementation

information is provided in the

ETX Design Guide

. Refer to those documents for additional

information.

9.4.2.

External SMI Interrupt

Contact Kontron Embedded Modules technical support for information on this feature.

9.5

Miscellaneous Circuits

9.5.1.

Speaker

The implementation of the speaker output complies with the

ETX Specification

Implementation information is provided in the

ETX Design Guide

. Refer to the

documentation for additional information.

9.5.2.

Battery

The implementation of the battery input complies with the

ETX Specification

Implementation information is provided in the

ETX Design Guide

. Refer to the

documentation for additional information.

In compliance with EN60950, on the

ETX-P3E/C3E

, there are at least two current-limiting

devices (resistor and diode) between the battery and the consuming component.

Содержание ETX Component SBC C3

































































Результаты поиска

Содержание ETX Component SBC C3

Отзывы:

Похожие инструкции для ETX Component SBC C3

Бренды по названию

Популярные бренды

Kontron ETX Component SBC C3, Руководство пользователя

Результаты поиска

Содержание ETX Component SBC C3

Отзывы:

Похожие инструкции для ETX Component SBC C3

Бренды по названию

Популярные бренды