manualshive.com logo in svg

Kontron ETX Component SBC C3, Руководство пользователя

Поделиться
Скачать
Kontron ETX Component SBC C3 Скачать руководство пользователя страница 16

Kontron

Specifications

ETX-P3/C3 User’s Guide

10

3.4 

Environmental Specifications

3.4.1. 

Temperature

!

 

Operating (with Kontron Embedded Modules heatspreader-plate  assembly):

•

 

Ambient temperature: 0 to +60 

°

C 

•

 

Maximum heatspreader plate temperature: 0 to +60 

°

C  (*)

!

 

Nonoperating: -10 to +85 

°

C 

See the 

Thermal Management

 chapter for additional information.

Note

: *The maximum operating temperature with the heatspreader plate is the maximum measurable temperature on

any spot on the heatspreader’s surface. You must maintain the temperature according to the above
specification.

!

 

Operating (without Kontron Embedded Systems heatspreader-plate assembly):

•

 

Maximum operating temperature: 0 to +60 °C (**)

!

 

Nonoperating: -10 to +85 

°

C

See the 

Thermal Management

 chapter for additional information.

Note

: ** The maximum operating temperature is the maximum measurable temperature on any spot on a module’s

surface. You must maintain the temperature according to the above specification.

3.4.2. 

Humidity

!

 

Operating: 10% to 90% (noncondensing)

!

 

Nonoperating: 5% to 95% (noncondensing)

Содержание ETX Component SBC C3

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды