Kontron AM4100 Скачать руководство пользователя

Страница: 133 / 150

AM4100

NetBootLoader

ID 36126, Rev. 2.0

Page 5 - 45

P R E L I M I N A R Y

T F T P

FUNCTION:

Download file from a TFTP server

SYNTAX:

tftp [<serverip>] [<filename>]

where:

tftp

command

parameter: string

<nnn.nnn.nnn.nnn>

IP address of the TFTP server

parameter: string

name of image file to be downloaded, or
path and name of image file to be downloaded

DESCRIPTION:

The TFTP command makes it possible to download a file from a
TFTP server via an Ethernet port. If used with the DHCP command, it
is possible to use the IP address and file information returned by the
DHCP command.

If this command is issued without any parameters, it will use the
previously stored information returned with the DHCP command.

USAGE:

Download a file from a TFTP server.

COMMAND / RESPONSE (none):

tftp 195.178.125.55 image2

This command downloads the file "image2" from the specified TFTP
server.

V E R

FUNCTION:

Display version number

SYNTAX:

ver

DESCRIPTION:

The command VER displays the actual version number of the
NetBootLoader.

Содержание AM4100























































































































































Результаты поиска

Содержание AM4100

Отзывы:

Похожие инструкции для AM4100

Бренды по названию

Популярные бренды

Kontron AM4100, Руководство пользователя

Результаты поиска

Содержание AM4100

Отзывы:

Похожие инструкции для AM4100

Бренды по названию

Популярные бренды