Kontron AM4100 Скачать руководство пользователя | Manualshive

Страница: 59 / 150

background image

AM4100

Installation

ID 36126, Rev. 2.0

Page 3 - 3

P R E L I M I N A R Y

3.

Installation

The AM4100 has been designed for easy installation. However, the following standard precau-
tions, installation procedures, and general information must be observed to ensure proper in-
stallation and preclude damage to the board, other system components, or injury to personnel.

3.1

Safety Requirements

The following safety precautions must be observed when installing or operating the AM4100.
Kontron assumes no responsibility for any damage resulting from failure to comply with these
requirements.

Warning!

Due care should be exercised when handling the board due to the fact that the
heat sink can get very hot. Do not touch the heat sink when installing or
removing the board.

In addition, the board should not be placed on any surface or in any form of
storage container until the board and heat sink have cooled down to room tem-
perature.

Warning!

This AMC board is equipped with an extraction/locking handle which makes it
possible to lock the board in a chassis/carrier during installation, or to unlock
and pull it out of the chassis/carrier during removal. When installing or remov-
ing the board, apply only as much force as required to lock/unlock the board or
to pull the board out of the chassis.

DO NOT

push on the extractor/locking handle to seat the board in the AMC

carrier/backplane connector.

Use of excessive force, bending or rotation of the handle will result in either
damage to the handle or the board locking mechanism. Kontron disclaims all
liability for damage to the board as a result of failure to comply with this warn-
ing.

ESD Equipment!

This AMC board contains electrostatic sensitive devices. Please observe the
necessary precautions to avoid damage to the board:

•

Discharge your clothing before touching the assembly. Tools must be dis-
charged before use.

•

Do not touch components, connector-pins or traces.

•

If working at an anti-static workbench with professional discharging
equipment, please do not omit to use it.

Warning!

This product has gold conductive fingers which are susceptible to contamina-
tion. Take care not to touch the gold conductive fingers of the AMC Card-edge
connector when handling the board.

Failure to comply with the instruction above may cause damage to the board
or result in improper system operation.

«
...
57
58
59
60
61
...
»

Содержание AM4100























































































































































Отзывы:

Нет отзывов

Похожие инструкции для AM4100

Бренд: ABB Страницы: 370

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 104

Бренд: ABB Страницы: 120

Бренд: ABB Страницы: 42

Бренд: Nelsen Corporation Страницы: 16

Бренд: National Instruments Страницы: 34

Бренд: VAT Страницы: 29

Бренд: Balboa Instruments Страницы: 19

Бренд: Yardney Страницы: 8

Бренд: Dakota Digital Страницы: 6

CMD-2000 Series

Бренд: Dakota Digital Страницы: 10

Бренд: Z-Wave Страницы: 6

Бренд: Yealink Страницы: 8

Бренд: B&G Страницы: 19

Бренд: Joy-it Страницы: 7

Бренд: Woodward Страницы: 112

Бренд: Ezodo Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды