Kontron AM4100 Скачать руководство пользователя

Страница: 105 / 150

AM4100

NetBootLoader

ID 36126, Rev. 2.0

Page 5 - 17

P R E L I M I N A R Y

C B L

FUNCTION:

Set or display the parameters of the bootline function

SYNTAX:

cbl [<num> (-|<bootline>)]

where:

cbl

command

<num>

parameter: string

0, 1, 2, 3, c

ID number of the image to be associated with the
bootline or bootline which is common to all images

no other values than those above are supported

option:

delete bootline for image specified or common

parameter: value: string (max. of 256 characters)

defines the bootline to be used with the kernel
indicated by <num> or the common bootline

DESCRIPTION:

When an image is programmed to NBL Flash memory, it is assigned
an ID number (0, 1, 2, or 3). This number is used to identify which
image is to be addressed by the command CBL.

In addition, a bootline common to all images may also be defined
using the “c” parameter.

If the command CBL is invoked without parameters, it returns the
contents of all bootlines.

Invoking the command CBL with the <bootline> parameter
overwrites any previous bootline for the image specified.

USAGE:

Display the bootline for image 2

COMMAND / RESPONSE:

cbl

Содержание AM4100























































































































































Результаты поиска

Содержание AM4100

Отзывы:

Похожие инструкции для AM4100

Бренды по названию

Популярные бренды

Kontron AM4100, Руководство пользователя

Результаты поиска

Содержание AM4100

Отзывы:

Похожие инструкции для AM4100

Бренды по названию

Популярные бренды