Konica Minolta DRYPRO Model 793 Скачать руководство пользователя | Manualshive

Страница: 15 / 156

background image

Ch.1 Safety Precautions & Warnings

< 13 >

DRYPRO Vstage MODEL 793 Operation Manual Ver.1.01 2005.1

NOTE : If the contents of this page are not legible, order a new manual.

Cautions for Safety

Thoroughly read the Cautions for Safety before use, and use the device correctly. Strictly observe all cau-

tions detailed here because they are quite important to secure the safe use of the device.

Cautions for Installation

• Never attempt to modify the device.

If you modify the device, this may cause a breakdown, electric shock, or fire.

• For installation, contact a sales office where you purchased this device or your Technical

Representative.

If you install the device and there are any problems in installation, this may cause an electric
shock or a fire.

• Be sure to ground the device well.

Never connect the grounding cable to the gas pipe, water supply pipe, lighting rod, or the ground-
ing cable for telephone.

• As for the electrical work (including grounding and communications cable work) follow the

local regulations on the technical standards.

If the work is not done properly, this may cause an electric shock or breakdown.

• Use the power supply with sufficient capacities according to the specifications.

If you use any power supply other than the specifications, or the power supply with insufficient
capacities, this may result in heating the electrical components or cause a fire.

WARNING

Cautions for Reinstallation, Storage and Repair

CAUTION

• In the event of detection of smoke, unusual odors or sounds, the power should be switched off

immediately and the power plug disconnected from the power outlet. Then contact your Konica Ser-
vice Representative. Continued use under such circumstances could result in fire.

Continued use of the device despite of such abnormality may result in damage, electric shock or fire.

• Contact your Technical Representative as to the reaction to the errors other than those listed in this

manual.

If the repair is done by the user with some failure, it may cause electric shock or fire.

• For reinstallation, storage and repair, contact a sales office where you purchased this device or your

Technical Representative.

If the device is relocated, reinstalled by the user with some failure, it may cause electric shock or fire.

«
...
13
14
15
16
17
...
»

Содержание DRYPRO Model 793





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DRYPRO Model 793

Color imageCLASS MF8580Cdw

Бренд: Canon Страницы: 36

Color imageCLASS MF8580Cdw

Бренд: Canon Страницы: 20

Color imageCLASS MF8280Cw

Бренд: Canon Страницы: 24

Color imageCLASS MF8080Cw

Бренд: Canon Страницы: 39

Color imageCLASS MF8050Cn

Бренд: Canon Страницы: 32

Color imageCLASS LBP7660Cdn

Бренд: Canon Страницы: 2

Color imageCLASS 8180c

Бренд: Canon Страницы: 24

Бренд: Canon Страницы: 30

C3000 - MultiPASS Color Inkjet Printer

Бренд: Canon Страницы: 41

Color imageCLASS MF8170c

Бренд: Canon Страницы: 2

Color imageCLASS MF8170c

Бренд: Canon Страницы: 98

Color imageCLASS MF8170c

Бренд: Canon Страницы: 8

Color imageCLASS MF8080Cw

Бренд: Canon Страницы: 46

Color imageRUNNER LBP5360

Бренд: Canon Страницы: 3

Бренд: Xerox Страницы: 341

Бренд: Datamax Страницы: 2

Бренд: Xerox Страницы: 48

Бренд: Oce Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды