Kondo KXR-L4D Скачать руководство пользователя

Страница: 11 / 71

Upper Case

Upper Axis （Final Axis）

Case Screw

Frame part installation hole

Groove surrounding the shaft.

The top of the shaft has a concave

origin; ﬁnd this position and install

the part.

This kit uses M3 screws.

This kit uses 2.6 - 4 screws.

The light comes on

when the power is on.

KRS-3301 ICS : Red

KRS-3304 ICS : Blue

This kit uses M2 screws.

Serration

Middle Case

Bottom Case

ZH connector

Whichever it is connected to,

there is no impact on operations.

Part Name of Servo Motor (KRS-3300 Series)

Origin

M3 Screw Hole

2.6 Tapping Screw Hole

LED

Align the protruding position and ﬁrmly insert all the way in.

Be careful not to push it in backward.

Frame parts are labeled Upper Side and Bottom Side to indicate

the installation direction.

Bottom Axis （Free Axis）

Bottom Side

Upper Side

Prior to Assembly

Servo Motor

Содержание KXR-L4D








































































Результаты поиска

Содержание KXR-L4D

Отзывы:

Похожие инструкции для KXR-L4D

Бренды по названию

Популярные бренды

Kondo KXR-L4D, Инструкция по сборке

Результаты поиска

Содержание KXR-L4D

Отзывы:

Похожие инструкции для KXR-L4D

Бренды по названию

Популярные бренды