Komfovent KLASIK CF Series Скачать руководство пользователя

Страница: 28 / 32

UAB KOMFOVENT we reserve the right to make changes without prior notice

KBP2-18-10

3.7. Connection of water heat exchangers

When connecting tubes for heaters/coolers, tubes

must be must be held with a pipe wrench; otherwise

these tubes will be damaged.

3.8. Air Dampers

Closing air dampers with aluminium or galvanized

steel blades are used in the units.

Air damper is fixed to the air handling unit with

screws.

Installing Electrical Drives on the Air Dampers.

Electrical Dampers Safety

The electrical actuators control air dampers of the air

handling unit.

1. Aluminum or galvanized steel blades

2. Rubber sealing

3. Plate shaft for the actuator

4. Shaft for bypass damper closing/opening

5. Fastening bend

6. Screw

1 2

1. Electric drive fixed to the air handling unit installed in a building

2. Electric drive fixed, under the cap, to the air handling unit installed outdoors

Direction of

rotation

If air handling unit is installed outside, then all the

drives outside have to be protected from moisture and

dust.

Содержание KLASIK CF Series

































Результаты поиска

Содержание KLASIK CF Series

Отзывы:

Похожие инструкции для KLASIK CF Series

Бренды по названию

Популярные бренды

Komfovent KLASIK CF Series, Руководство по установке

Результаты поиска

Содержание KLASIK CF Series

Отзывы:

Похожие инструкции для KLASIK CF Series

Бренды по названию

Популярные бренды