manualshive.com logo in svg

Komatsu PC500LC-10R, Руководство по ремонту, Страница: 504 / 758

Поделиться
Скачать
Komatsu PC500LC-10R Скачать руководство пользователя страница 504

2.

Disconnect  the  drain  hose  (4).  Block  the  hose  side  with
plug C.

3.

Turn the swing lock switch to ON position.

4.

Start the engine.

5.

Select and display “Pre-defined Monitoring” (01/11) by re-
ferring to “SET AND OPERATE MACHINE MONITOR”.

6.

Adjust the hydraulic oil temperature so that it is within the
specified range.

7.

Turn the fuel control dial to MAX (High idle) position.

8.

Operate  the  swing  control  lever  to  relieve  the  pressure  in
the swing circuit.

9.

Measure the oil leakage for 1 minute 30 seconds after the oil pressure is relieved.
See STANDARD VALUE TABLE, “STANDARD VALUE TABLE FOR MACHINE” for standard values.

10. After finishing the above test, swing the upper structure 180 °, and then start the test again.
Restore the machine after finishing the test.

METHOD FOR TESTING OIL LEAKAGE FROM TRAVEL MOTOR

1.

Remove the travel motor cover.

2.

Start the engine, insert the plate D and pin E between the
sprocket  and  track  frame  to  securely  lock  the  track,  and
stop the engine.

3.

Disconnect  the  drain  hose  (5)  of  the  travel  motor,  and
block the hose side by using a plug C.

4.

Start the engine.

5.

Select and display “Pre-defined Monitoring” (01/11) by re-
ferring to “SET AND OPERATE MACHINE MONITOR”.

6.

Adjust the hydraulic oil temperature so that it is within the
specified range.

7.

Turn the fuel control dial to MAX (High idle) position.

8.

Relieve the oil pressure from the travel circuit by perform-
ing operation of the travel lever and pedal.

k

 Be sure to perform correct lever operation by using clear hand signals and checking. Otherwise

wrong lever operation can be a cause of an accident.

k

 Before operating the travel lever, check the position and direction of locked sprocket again.

9.

Measure the oil leakage for 1 minute 30 seconds after the oil pressure is relieved.
See STANDARD VALUE TABLE, “STANDARD VALUE TABLE FOR MACHINE” for standard values.

10. Move the motor a little each time and test the oil leakage several times (changing the relative position be-

tween the valve plate and cylinder and that between the cylinder and piston).

Restore the machine after finishing the test.

TEST OIL LEAKAGE

30 TESTING AND ADJUSTING

30-98

PC500LC-10R

Содержание PC500LC-10R























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов